Fracture toughness of PAN-based carbon fibers estimated from strength-mirror size relation

Fracture toughness (K_IC) of representative high-strength type PAN (polyacrylonitrile)-based carbon fibers, Torayca™ T300 and T800H, with or without artificial surface defects, were estimated to be ca. 1 MPam^1/2 from the tensile strength vs. fracture mirror size relation, assuming a constant crack-to-mirror size ratio. The corresponding critical energy release rate (Γ) was ca. 7.4 J m⁻², which was close to the value derived from the reported surface energies for a graphite crystal. Similar K_IC values were obtained for the old-type PAN-based carbon fibers from the reported data by the use of the present estimation procedure.     

激光熔覆Ni基B4C合金涂层的组织与性能研究

利用5kW连续波CO2激光器对16Mn钢基材表面预置的含20 vol%B4CP的Ni基合金复合粉末进行激光熔覆得到Ni基B4C合金涂层(NiB4c),研究了NiB4c涂层的组织形貌与相组成,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiB4C涂层由涂层下部的胞状晶和涂层中上部的树状枝晶及其间的共晶组织所组成,其组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,CrB,Ni3B,Fe2B,Fe23(C,B)6等化合物,涂层中存在未熔的B4C颗粒。激光熔覆NiB4c涂层比Ni60涂层具有较高的硬度和耐磨性,并分析了NiB4C涂层的强化机理。     

光电设备电子机柜布线工艺研究

作为信号和电能载体的导线，同时也是噪声的载体和外来噪声侵入设备的媒体。描述了噪声通过导线侵入设备内部的方式，通过降低噪声的途径确定了机柜布线的原则，介绍了布线的要求和方法，最后提出了用布线槽布线的建议。     

串行及并行A/D转换器在高速数据采集中的采样差别性分析

串行和并行接口模式是A/D转换器诸多分类中的一种,但却是应用中器件选择的一个重要指标.在同样的转换分辨率及转换速度的前提下,不同的接口方式不但影响了电路结构,更重要的是将在高速数据采集的过程中对采样周期产生较大影响.本文通过12位串行ADC ADS7822和并行ADC ADS774与AT89C51的接口电路,给出二者采样时间的差异性.     

Al-10Mg型固溶合金自然时效稳定性研究

测定了ZL30 5合金自然时效 33年的力学性能变化 ,观察了晶界的析出相 ,研究了组织和性能的关系 ,从而确定了ZL30 5合金具有长期自然时效稳定性。     

Fracture and deformation properties of Ni-Fe superalloy in cryogenic high magnetic field environments

The present paper includes experimental and analytical data on the fracture properties of a nickel-iron superalloy, a ferromagnetic austenite, at 4 K in magnetic fields of 0 and 6 T. The tensile, notch tensile and small punch tests are employed. A finite element analysis is also performed to convert the experimentally measured load-displacement data into useful engineering information. To interpret the results we review the available theory of the influence of magnetic field on the stress intensity factor for a crack in ferromagnetic materials.     

Failure mode transition and energy dissipation in naturally occurring composites

The microstructural aspects of compressive inelastic deformation in balsa wood are investigated with emphasis on the failure mode transition and its effects on energy dissipation characteristics. The architectural features as well as the composite character of cell wall ultrastructure are discussed in a framework to understand the complex interrelationship between microstructure and macroscopic behavior in this extremely lightweight cellular biocomposite. Based on this discussion and experimental results, it is concluded that the biomimetic approach may prove to be a viable strategy in designing composite structures with high specific energy absorption capacity.     

双电池系统电源选择器MAX1773/1773A

MAX1773／MAX1773A是用于双电池系统的电源选择器，它允许外部控制器去管理双电池组、适配器输入、电池充电器和系统负载所需的电源连接。文中介绍了MAX1773／1773A的特点、引脚功能、内部结构和工作原理，给出了MAX1773/MAX1773A的典型工作电路。     

X-ray diffraction and Raman scattering in SbSI nanocrystals

Lattice structure and rod-like shaped SbSI nanocrystals obtained by ball milling with rod thickness down to 70 nm, as estimated from X-ray diffraction (XRD) and electron microscopy, is similar to that of the bulk crystals. The dependence of the grain size on the milling duration is discussed in view of the chain-like crystalline structure of SbSI. Possible factors, responsible for the observed Raman line broadening, are discussed, scattering by surface phonons being considered the predominant one.     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.